Swing clamps, with threaded body
Hydrokomp Hydraulische Komponenten GmbH Logo

Select your language

Inquiry list

Swing clamps, with threaded body, for drilled channels (D)

 

Swing clamp,
with threaded body, for drilled channels, integrated overload protection

 

Risk of injury:
If the swing clamp cylinder is under pressure considerable risks of injury by pinching or crushing are constantly present within the swing area during operation.
The safety instructions and the valid accident prevention regulations must be observed.

 

Description

Swing clamp cylinders release the clamping point on the workpiece. With this, it is easy to change the workpiece. This hydraulic swing clamp cylinder operates as single-acting or double-acting traction cylinder, whereas part of the stroke is used to rotate the piston. The model with 0° swing angle operates only vertical as traction cylinder. To guarantee a long lifetime the cylinders have an integrated metal wiper as standard.

The oil supply is made through drilled channels. The seal takes place directly in the mounting hole. You can select between right or left turning models with various standardized swing angles. The integrated overload protection protects the swing mechanism from damage due blockage of the rotation or improper assembly of the clamping arm.

For any risk of exceeding the permitted volume flow a throttle check valve must be interposed into the oil supply line. Counter-hold the clamping arm when tightening or loosening the counter nut in order to prevent torque transfer to the piston rod and to avoid damage to the ball guide. Variations with 0°, 30°, 45°, 60° and 90° swing angles are available. The permitted operating pressure is depending from the clamping arm length.

Except from standard clamping arms also special clamping arms can be assembled. The maximum operating pressure of 500 bar does not apply for each clamping arm length. For details about the permitted operating pressure, see data sheet.

When installing the cylinder pay attention on precise cleanness in the oil passages.

 

Ventilation for single-acting swing clamp cylinders:

In order to avoid malfunctions, the spring chamber of the single-acting swing clamp cylinder must be vented. The penetration of foreign particles and liquids into the spring chamber must be prevented eg. by a sintered metal filter. If necessary, an additional vent line can be connected.

(The sintered metal filter and the vent line are not included in scope of supply.)


Application examples:

 


 

 

L = in basic position, 90° left turning

R = in basic position, 90° right turning

 

 

Special features:
  • protecting metal wiper

  • integrated overload protection

  • pipeless oil supply via drilled channels

  • easy loading and unloading of the fixture

  • customer specific clamping arms can be mounted

  • standard and special clamping arms available

 

Design:


Type D, threaded body without flange

The dimensioned installation contour can be found on the data sheet.

 

Clamping arm holder:


Taper, ratio 1:10

Clamping arms:

  • SPK/c single clamping arm
  • SPK/d single clamping arm
  • SPK/e single clamping arm
  • SPK/f  double clamping arm
 
Here you will find an overview of all standard clamping arms.
Special clamping arms are available on request.
 
 

 

 

Hotline

We gladly consult you by phone call:

Customer service on-site

Find a consultant in your area!

Weltkarte mit HYDROKOMP Vertriebspartnerländern weltweit

Technology that connects

HYDROKOMP Headquarters 1

Founded 1998, HYDROKOMP designs, manufactures and distributes hydraulic components, coupling systems and clamping technology for mechanical engineering, fixture construction, tooling and many other branches of industry also for different operating conditions.

HYDROKOMP Headquarters 2

HYDROKOMP is the right supplier for companies of mechanical engineering fixture construction, tooling and many other branches of industry worldwide. Constructive ideas and customer-specific designs are our particular strengths.

HYDROKOMP Production Facility 1

Each and every one of our products is developed and manufactured according to the highest quality standards. With modern CAD systems we design new solutions. After that, current procedures of precision manufacture and quality assurance are next in process.

HYDROKOMP Production Facility 2

Our qualified employees and our modern CNC machinery ensure high flexibility product variety and quality. HYDROKOMP products are designed for long-lasting application in rough industrial daily routine. Our customers can surely trust that the process will flow smoothly.

previous arrow
next arrow

 

 

We use cookies on our website. Some of them are essential for the operation of the site, while others help us to improve this site and the user experience (tracking cookies). You can decide for yourself whether you want to allow cookies or not. Please note that if you reject them, you may not be able to use all the functionalities of the site.